ezg_8ea

[ Pobierz całość w formacie PDF ]

COWL TOP TRIM PANEL place.
WARNING: ON VEHICLES EQUIPPED WITH AIR- (1) Disconnect and isolate the battery negative
cable.
BAGS, REFER TO GROUP 8M - PASSIVE
(2) Remove the steering column opening cover and
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
knee blocker from the instrument panel. See Steering
STEERING WHEEL, STEERING COLUMN, OR
Column Opening Cover and Knee Blocker in this
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
SERVICE. FAILURE TO TAKE THE PROPER PRE- group for the procedures.
CAUTIONS COULD RESULT IN ACCIDENTAL AIR- (3) Remove the cluster bezel from the instrument
panel. See Cluster Bezel in this group for the proce-
BAG DEPLOYMENT AND POSSIBLE PERSONAL
dures.
INJURY.
(4) Remove the glove box module from the instru-
(1) Disconnect and isolate the battery negative
ment panel. See Glove Box Module in this group for
cable.
the procedures.
(2) Using a trim stick or another suitable wide
(5) Remove the cowl top trim panel from the
flat-bladed tool, gently pry the cowl top trim panel off
instrument panel. See Cowl Top Trim Panel in this
of the instrument panel top pad (Fig. 21).
group for the procedures.
(3) Pull the trim panel up far enough to access and
(6) If the vehicle is so equipped, remove the screw
unplug the wire harness connector for the solar sen-
that secures the auto headlamp light sensor/vehicle
sor, or to remove the solar sensor from the cowl top
theft security system lamp to the top of the instru-
trim, if the vehicle is so equipped.
ment panel near the defroster duct outlet, and move
(4) Remove the cowl top trim panel from the
it far enough for clearance during removal of the
instrument panel.
instrument panel top pad.
(5) Reverse the removal procedures to install.
(7) Remove all of the screws that secure the perim-
eter of the instrument panel top pad to the instru-
INSTRUMENT PANEL TOP PAD
ment panel armature.
(8) Remove the instrument panel top pad from the
WARNING: ON VEHICLES EQUIPPED WITH AIR-
instrument panel armature.
BAGS, REFER TO GROUP 8M - PASSIVE
ZG INSTRUMENT PANEL SYSTEMS 8E - 35
REMOVAL AND INSTALLATION (Continued)
(9) Reverse the removal procedures to install. (8) Remove the junction block from the mounting
Tighten the mounting screws to 2.2 N�m (20 in. lbs.). bracket on the right cowl side inner panel.
(9) Reverse the removal procedures to install.
JUNCTION BLOCK Tighten the mounting screws to 2.2 N�m (20 in. lbs.).
WARNING: ON VEHICLES EQUIPPED WITH AIR-
INSTRUMENT PANEL ASSEMBLY
BAGS, REFER TO GROUP 8M - PASSIVE
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY WARNING: ON VEHICLES EQUIPPED WITH AIR-
STEERING WHEEL, STEERING COLUMN, OR BAGS, REFER TO GROUP 8M - PASSIVE
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
SERVICE. FAILURE TO TAKE THE PROPER PRE- STEERING WHEEL, STEERING COLUMN, OR
CAUTIONS COULD RESULT IN ACCIDENTAL AIR- INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
BAG DEPLOYMENT AND POSSIBLE PERSONAL SERVICE. FAILURE TO TAKE THE PROPER PRE-
INJURY. CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
BAG DEPLOYMENT AND POSSIBLE PERSONAL
(1) Disconnect and isolate the battery negative
INJURY.
cable.
(2) Remove the fuse access panel by unsnapping it (1) Disconnect and isolate the battery negative
from the right cowl side trim panel. cable.
(3) Remove the push nut that secures the right (2) Remove the steering column opening cover and
cowl side trim panel to the junction block stud (Fig. knee blocker from the instrument panel. See Steering
22). Column Opening Cover and Knee Blocker in this
group for the procedures.
(3) Remove the bolts that secure the lower instru-
ment panel reinforcement to the instrument panel
armature and remove the reinforcement (Fig. 23).
(4) Remove the upper and lower steering column
shrouds from the steering column. Refer to Group 19
- Steering for the procedures.
(5) Unplug all of the wire harness connectors from
the steering column-mounted components and
switches.
(6) Remove the three nuts that secure the steering
column toe plate to the dash panel at the base of the
steering column.
(7) Remove the two nuts that secure the steering
column mounting bracket to the studs on the steer-
ing column and brake pedal support. Lower the
steering column to the floor.
(8) Remove both cowl side trim panels. Refer to
Group 23 - Body for the procedures.
(9) Unplug the instrument panel to body wire har-
ness connector under the left end of the instrument
panel.
(10) Unplug the brake lamp switch wire harness
Fig. 22 Right Cowl Side Trim Panel Remove/Install
connector.
(4) Remove the two screws that secure the right
(11) Unplug the instrument panel to heater-A/C
cowl side trim panel to the right front door opening
housing vacuum harness connector (manual temper-
trim.
ature control only) and wire harness connector
(5) Remove the right cowl side trim panel from the
located under the passenger side end of the instru- [ Pobierz całość w formacie PDF ]

Odnośniki